K 10 svn:author V 3 ken K 8 svn:date V 27 2013-08-26T21:34:43.977984Z K 7 svn:log V 8907 MFC mps(4) driver changes 253460, 253549, 253550 and 254615. There are some slight changes here from the version in head. __FreeBSD_version has been bumped to 902502 for the inclusion of the PIM_RESCAN CAM path inquiry flag. The ifdefs in the mps(4) driver have been changed accordingly. In head, the TDP_NOSLEEPING thread flag has been removed but it still exists in stable/9. ------------------------------------------------------------------------ r253460 | scottl | 2013-07-18 18:12:41 -0600 (Thu, 18 Jul 2013) | 5 lines Overhaul error, information, and debug logging. Obtained from: Netflix ------------------------------------------------------------------------ r253549 | ken | 2013-07-22 12:37:07 -0600 (Mon, 22 Jul 2013) | 57 lines CAM and mps(4) driver scanning changes. Add a PIM_NOSCAN flag to the CAM path inquiry CCB. This tells CAM not to perform a rescan on a bus when it is registered. We now use this flag in the mps(4) driver. Since it knows what devices it has attached, it is more efficient for it to just issue a target rescan on the targets that are attached. Also, remove the private rescan thread from the mps(4) driver in favor of the rescan thread already built into CAM. Without this change, but with the change above, the MPS scanner could run before or during CAM's initial setup, which would cause duplicate device reprobes and announcements. sys/param.h: Bump __FreeBSD_version to 1000039 for the inclusion of the PIM_RESCAN CAM path inquiry flag. sys/cam/cam_ccb.h: sys/cam/cam_xpt.c: Added a PIM_NOSCAN flag. If a SIM sets this in the path inquiry ccb, then CAM won't rescan the bus in xpt_bus_regsister. sys/dev/mps/mps_sas.c For versions of FreeBSD that have the PIM_NOSCAN path inquiry flag, don't freeze the sim queue during scanning, because CAM won't be scanning this bus. Instead, hold up the boot. Don't call mpssas_rescan_target in mpssas_startup_decrement; it's redundant and I don't know why it was in there. Set PIM_NOSCAN in path inquiry CCBs. Remove methods related to the internal rescan daemon. Always use async events to trigger a probe for EEDP support. In older versions of FreeBSD where AC_ADVINFO_CHANGED is not available, use AC_FOUND_DEVICE and issue the necessary READ CAPACITY manually. Provide a path to xpt_register_async() so that we only receive events for our own SCSI domain. Improve error reporting in cases where setup for EEDP detection fails. sys/dev/mps/mps_sas.h: Remove softc flags and data related to the scanner thread. sys/dev/mps/mps_sas_lsi.c: Unconditionally rescan the target whenever a device is added. Sponsored by: Spectra Logic ------------------------------------------------------------------------ r253550 | ken | 2013-07-22 12:41:53 -0600 (Mon, 22 Jul 2013) | 93 lines Merge in phase 14+ -> 16 mps driver fixes from LSI: --------------------------------------------------------------- System panics during a Port reset with ouststanding I/O --------------------------------------------------------------- It is possible to call mps_mapping_free_memory after this memory is already freed, causing a panic. Removed this extra call to mps_mappiing_free_memory and call mps_mapping_exit in place of the mps_mapping_free_memory call so that any outstanding mapping items can be flushed before memory is freed. --------------------------------------------------------------- Correct memory leak during a Port reset with ouststanding I/O --------------------------------------------------------------- In mps_reinit function, the mapping memory was not being freed before being re-allocated. Added line to call the memory free function for mapping memory. --------------------------------------------------------------- Use CAM_SIM_QUEUED flag in Driver IO path. --------------------------------------------------------------- This flag informs the XPT that successful abort of a CCB requires an abort ccb to be issued to the SIM. While processing SCSI IO's, set the CAM_SIM_QUEUED flag in the status for the IO. When the command completes, clear this flag. --------------------------------------------------------------- Check for CAM_REQ_INPROG in I/O path. --------------------------------------------------------------- Added a check in mpssas_action_scsiio for the In Progress status for the IO. If this flag is set, the IO has already been aborted by the upper layer (before CAM_SIM_QUEUED was set) and there is no need to send the IO. The request will be completed without error. --------------------------------------------------------------- Improve "doorbell handshake method" for mps_get_iocfacts --------------------------------------------------------------- Removed call to get Port Facts since this information is not used currently. Added mps_iocfacts_allocate function to allocate memory that is based on IOC Facts data. Added mps_iocfacts_free function to free memory that is based on IOC Facts data. Both of the functions are used when a Diag Reset is performed or when the driver is attached/detached. This is needed in case IOC Facts changes after a Diag Reset, which could happen if FW is upgraded. Moved call of mps_bases_static_config_pages from the attach routine to after the IOC is ready to process accesses based on the new memory allocations (instead of polling through the Doorbell). --------------------------------------------------------------- Set TimeStamp in INIT message in millisecond format Set the IOC --------------------------------------------------------------- --------------------------------------------------------------- Prefer mps_wait_command to mps_request_polled --------------------------------------------------------------- Instead of using mps_request_polled, call mps_wait_command whenever possible. Change the mps_wait_command function to check the current context and either use interrupt context or poll if required by using the pause or DELAY function. Added a check after waiting 50mSecs to see if the command has timed out. This is only done if polliing, the msleep command will automatically timeout if the command has taken too long to complete. --------------------------------------------------------------- Integrated RAID: Volume Activation Failed error message is displayed though the volume has been activated. --------------------------------------------------------------- Instead of failing an IOCTL request that does not have a large enough buffer to hold the complete reply, copy as much data from the reply as possible into the user's buffer and log a message saying that the user's buffer was smaller than the returned data. --------------------------------------------------------------- mapping_add_new_device failure due to persistent table FULL --------------------------------------------------------------- When a new device is added, if it is determined that the device persistent table is being used and is full, instead of displaying a message for this condition every time, only log a message if the MPS_INFO bit is set in the debug_flags. Submitted by: LSI ------------------------------------------------------------------------ r254615 | ken | 2013-08-21 15:30:56 -0600 (Wed, 21 Aug 2013) | 32 lines Fix mps(4) driver breakage that came in in change 253550 that manifested itself in out of chain frame conditions. When the driver ran out of chain frames, the request in question would get completed early, and go through mpssas_scsiio_complete(). In mpssas_scsiio_complete(), the negation of the CAM status values (CAM_STATUS_MASK | CAM_SIM_QUEUED) was ORed in instead of being ANDed in. This resulted in a bogus CAM CCB status value. This didn't show up in the non-error case, because the status was reset to something valid (e.g. CAM_REQ_CMP) later on in the function. But in the error case, such as when the driver ran out of chain frames, the CAM_REQUEUE_REQ status was ORed in to the bogus status value. This led to the CAM transport layer repeatedly releasing the SIM queue, because it though that the CAM_RELEASE_SIMQ flag had been set. The symptom was messages like this on the console when INVARIANTS were enabled: xpt_release_simq: requested 1 > present 0 xpt_release_simq: requested 1 > present 0 xpt_release_simq: requested 1 > present 0 mps_sas.c: In mpssas_scsiio_complete(), use &= to take status bits out. |= adds them in. In the error case in mpssas_scsiio_complete(), set the status to CAM_REQUEUE_REQ, don't OR it in. Sponsored by: Spectra Logic ------------------------------------------------------------------------ END